Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Spring Replacement Cost in Pasadena?
Spring replacement in Pasadena typically costs $180 – $340 per spring, installed. Most residential doors run two springs, so a matched pair is usually replaced together at roughly twice that range. The written estimate you get on site sets the final price, and estimates are free.
If your door slammed shut or stopped opening this morning, a broken spring is the usual reason. These are high-tension components under serious load, and they’re not a DIY fix. Our technicians have up to 9 years of experience, and they’re familiar with the door and opener systems found on homes across Pasadena, from older extension-spring doors near the Port to newer torsion setups in Deer Park-adjacent subdivisions. Call (855) 943-1327 for a free estimate. We answer 24/7, and fast dispatch from 7am to 7pm gets a technician to your door Sunday through Friday.
Key Takeaways
- One spring: $180 – $340. A matched pair: about twice that, because both usually fail close together.
- Torsion and extension springs both demand proper tools and training. A spring under tension can cause injury if handled wrong.
- We know the major brands: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor, so the right replacement part is matched the first time.
- Free estimates. The written quote is the price.
- Same-day service is often possible when you call early. Fast dispatch from 7am to 7pm, Sunday through Friday.
Spring Replacement Cost Breakdown (2026)
Here’s how spring work typically prices out in the Pasadena market. These are estimated ranges for a standard residential door. A matched pair of springs costs about twice the per-spring figure, since both are almost always replaced at the same time.
| Job | Typical Estimated Cost |
|---|---|
| Single torsion spring replacement | $180 – $340 |
| Single extension spring replacement | $180 – $340 |
| Matched pair (replaced together) | About twice the single-spring range |
| Spring repair (re-tension, hardware) | $180 – $340 |
| Cable repair (often needed alongside) | $130 – $250 |
| Roller replacement | $110 – $220 |
| Track realignment | $120 – $240 |
| Panel replacement | $250 – $500 |
| Opener repair | $120 – $320 |
| Opener installation | $250 – $550 |
| General garage door repair | $150 – $600 |
| New door installation | $700 – $2,200 |
What moves the number up or down? The spring type matters first: a heavy door or a high-lift setup can call for a higher-cycle spring, which costs more than a standard one. A pair costs about twice a single. If a frayed cable snapped when the spring let go, add the cable repair range. On older doors, worn rollers or a bent track often surface once the door comes off its springs, and fixing those now saves a second visit later. The written estimate after a technician looks at the door is what sets your final price, so there are no surprises.
For a closer look at how spring work fits into the bigger picture of door service, see spring replacement, and for the full range of door work we handle, visit Garage Door Repair Pasadena Pros.
What Affects Spring Replacement Pricing in Pasadena
- Spring type and cycle rating. Torsion springs mounted on a shaft above the door and extension springs running along the sides are priced differently, and a higher-cycle spring built for heavier daily use costs more than a standard one. A technician will match the spring to your door’s weight, not just drop in whatever fits.
- One spring or the pair. Springs are usually replaced as a matched pair, because when one breaks the other has lived the same number of cycles and is likely to fail soon after. Budget for roughly double the single-spring range when both go.
- Door weight and size. A wide, insulated double door in a newer Pasadena subdivision carries more weight than a single-bay door on an older home, and heavier doors need stronger springs. Insulation matters here: the Gulf Coast heat and humidity push many homeowners toward insulated doors, which changes the spring spec.
- Condition of cables, rollers and track. A broken spring often exposes worn cables or a misaligned track. Correcting those in the same visit adds from the cable, roller or track ranges above, but beats paying for a second trip later.
- Access and door setup. Low-headroom doors, high-lift tracks and doors with a lot of hardware take more time to work on safely, and that time shows up in the estimate.
- Whether it’s a repair or a replacement. Re-tensioning or repairing existing hardware sometimes lands at the low end of the range, while a full spring swap with new cables sits higher.
If you’re weighing a repair against a new door altogether, it helps to compare the spring range against the new door installation range. A door that’s otherwise sound and just needs springs is almost always the better spend.
Can a Broken Spring Wait, or Do I Need It Fixed Today?
A broken spring should be fixed before the door is used again, because forcing a door with a dead spring can bend the track, strip the opener, or send the door down hard. Treat a snapped spring as a stop-use situation until a technician has looked at it. That’s the honest answer, and it’s why spring calls jump the line.
When the door won’t open, your garage and the car inside it are exposed, and the door itself can be a genuine safety risk if it’s hanging unevenly. That’s where emergency garage door service comes in. We answer 24/7, and fast dispatch from 7am to 7pm runs Sunday through Friday. A call outside those dispatch hours is booked into the next opening. Same-day service is often possible when you reach us early in the day.
How to Save on Spring Replacement
The best savings on spring work come from catching problems before they compound. A few practical habits:
- Replace the pair, not one. It costs about twice a single spring up front, but replacing one tired spring on a matched pair usually means paying for a second visit soon after. Doing both at once is cheaper over the year.
- Fix cables and rollers in the same visit. Bundling a cable or roller fix into the spring job avoids a separate call and keeps the door balanced.
- Listen for the warning signs. A door that’s getting harder to lift, squeaks loudly, or closes unevenly often signals a spring nearing the end. Getting it checked before it snaps can keep you at the lower end of the range and out of an emergency.
- Keep the door balanced. A properly balanced door puts less strain on the springs and the opener, which stretches how long the springs last.
- Get a written estimate first. Free estimates mean you know the number before any work starts. Call (855) 943-1327 and we’ll price it out at no charge.
Saving money here is really about avoiding a second visit and a surprise breakdown, not about hunting for the cheapest quote, which often means a spring that’s undersized for your door. A spring matched to the door’s actual weight is the one that lasts.
Why Brand Knowledge Keeps the Price Right
Pasadena homes run the full spread of door and opener brands, and knowing the system before the technician arrives keeps the job tight and the price honest. We work with equipment from LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. That matters when a spring job ties into opener settings or door hardware that need to match a specific make. Sourcing the correct replacement part the first time means fewer return visits and no guessing, which is exactly how you keep a spring repair from creeping up the range.
Springs are high-tension parts, and a generalist guessing at the right spring or the right tension is a recipe for a door that’s out of balance or a part that fails early. Torsion and extension springs call for specific tools and training, and our technicians handle that work directly. When it can’t wait, that same team is who you reach.
Repair or Replace: Which Makes Sense for Your Door?
If the door panels, track and opener are in decent shape and only the springs have failed, repairing the springs is the clear call, and it lands in the $180 – $340 per spring range. Replacing the whole door only makes sense when the panels are rusted through, the door is badly out of square, or you’re upgrading to an insulated door for the Gulf Coast heat. In that case, new door installation runs $700 – $2,200, and the spring work is built into the install.
A technician can tell you honestly which side of that line your door is on after a look. That’s a free estimate, and it’s the fastest way to know whether you’re spending a few hundred or a couple thousand. Call (855) 943-1327. We answer 24/7, with fast dispatch from 7am to 7pm Sunday through Friday, and we’re closed Saturday.
Same-Day Repair and What Happens When You Call
Spring failures usually get handled the same day you call, especially if you reach us in the morning. Here’s how it goes: you call, we ask a couple of questions about the door and the sound it made, and we set a dispatch window. A technician arrives with the tools and the right spring spec for your door, confirms the diagnosis, and gives you the written estimate before any work starts. Once you approve it, the springs get swapped, the door gets balanced and tested, and you’re back up and running today.
We know your brand, so the part is matched correctly the first time. Our technicians have up to 9 years of experience across the major door and opener makes, and brand-specific diagnostics mean fewer return visits. Call (855) 943-1327. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Closed Saturday, so a call then is booked into the next opening.
FAQs – Spring Replacement Cost
How much does spring replacement cost in Pasadena?
Spring replacement in Pasadena typically costs $180 – $340 per spring, installed, and a matched pair is usually replaced together at roughly double that range. The written estimate sets the final price, and estimates are free. Call (855) 943-1327 for an exact quote.
Is it cheaper to repair or replace a garage door spring?
Repairing or replacing the failed spring almost always costs less than a new door, and it’s the right move when the door itself is sound. Spring work runs $180 – $340 per spring, while a full new door installation runs $700 – $2,200. Compare the two only if the panels or track are also failing. Call (855) 943-1327 and we’ll tell you which makes sense for your door.
Do I need to replace both springs at once?
In most cases, yes. A pair of springs shares the same cycle count, so when one breaks the other is close behind, and replacing both together costs about twice the single-spring range but saves a second visit. Call (855) 943-1327 for a free estimate on the pair.
Can you come today if my spring is broken?
Same-day service is often possible when you call early in the day, and a broken spring is treated as a priority because the door shouldn’t be used until it’s fixed. Fast dispatch from 7am to 7pm runs Sunday through Friday, and we answer the phone 24/7. Call (855) 943-1327 to book the next opening.
What other repairs might add to the spring replacement cost?
A frayed cable usually adds $130 – $250, and worn rollers or a bent track add from $110 – $220 and $120 – $240 respectively when they need fixing in the same visit. Bundling them into the spring job is cheaper than a separate call. Call (855) 943-1327 for a free estimate that covers the whole job.
Written by the team at Garage Door Repair Pasadena Pros.
Pricing reflects the Pasadena market as of 2026. Garage Door Repair Pasadena Pros offers free estimates – call (855) 943-1327.
What Our Customers Say
"Opener kept reversing halfway down. Turned out to be the safety sensors knocked out of alignment by a bicycle. He straightened them, wouldn't charge me for it, and just asked me to keep them in mind if I need real work later."
- Carmen Guzman"Logic board on a 15 year old opener. He was upfront that a new opener would cost less than the board plus labor, and he wasn't wrong. No pressure either way."
- Rosa Vargas"Track was bent and two of the rollers were shot. He straightened what he could, swapped the rollers for nylon ones, lubricated everything, and had it done in about an hour."
- Bryce Hoffman